621.91
   Р 49


    Різання та інструменти в технологічних системах [Текст] = Cutting & Tools in Technological Systems : міжнар. наук.-техн. зб. / НТУ “ХПі” ; голов. ред. А. І. Грабченко.
   Вип. 94. - Харків : НТУ “ХПІ”, 2021. - 152 с. : табл., рис. - ISSN 2078-7405. - 66.00 грн
Попередня назва : : Резание и инструмент в технологических системах. - Харьков : НТУ “ХПИ”
Резание и инструменты в технологических системах. - Харьков : НТУ “ХПИ”
    Зміст:
Balanou, M. Experimental investigation of surface topography of al7075–t6 alloy machined by edm / M. Balanou, E. I. Papazoglou, A. P. Markopoulos. - P .3-10. - Bibliography is at the end of the article
Кл.слова: ЕЛЕКТРОЕРОЗІЙНА ОБРОБКА, АЛЮМІНІЄВІ СПЛАВИ, ТОПОГРАФІЯ ПОВЕРХНІ
Veres, P. The importants of clustering in logistic systems / P. Veres. - P .11-18. - Bibliography is at the end of the article
Кл.слова: КЛАСТЕРИЗАЦІЯ, ЕВРИСТИКА, МАРШРУТИЗАЦІЯ
Dyadya, S. Simulation of the machined surface after end milling with self–oscillations / S. Dyadya [and enc.]. - P .19-27. - Bibliography is at the end of the article
Інші автори: Kozlova Ye., Germashev A., Logominov V.
Кл.слова: ФРЕЗЕРУВАННЯ, АВТОКОЛИВАННЯ, МОДЕЛЮВАННЯ
Oliinyk, S. Technological fixtures for machining large-sized thin–walled shells of complex profile / S. Oliinyk, L. Kalafatova. - P .28-41. - Bibliography is at the end of the article
Кл.слова: ТОНКОСТІННА ОБОЛОНКА, СИТАЛ, АЛМАЗНЕ ШЛІФУВАННЯ
Mitsyk, A. Interaction of the abrasive medium with the treated surface and the process of metal removal during vibration treatment in the presence of a chemically active solution / A. Mitsyk, V. Fedorovich, A. Grabchenko. - P .42-48. - Bibliography is at the end of the article
Кл.слова: АБРАЗИВНЕ СЕРЕДОВИЩЕ, ПОВЕРХНЕВИЙ ШАР, МЕХАНО-ФІЗИКО-ХІМІЧНА МОДЕЛЬ
Molnár, V. Tribology and topography of hard machined surfaces / V. Molnár. - P .49-59. - Bibliography is at the end of the article
Кл.слова: ЖОРСТКЕ ТОЧІННЯ, ВРІЗНЕ ШЛІФУВАННЯ, ТРИВИМІРНА ШОРСТКІСТЬ ПОВЕРХНІ
Nagy, A. Investigation of the effect of areal roughness measurement length on face milled surface topographies / A. Nagy. - P .60-69. - Bibliography is at the end of the article
Кл.слова: ШОРСТКІСТЬ ПРОФІЛЮ, ШОРСТКІСТЬ ПОВЕРХНІ, ДОВЖИНА ВИМІРЮВАННЯ
Sztankovics, I. The effect of the circular feed on the surface roughness and the machining time / I. Sztankovics. - P .70-76. - Bibliography is at the end of the article
Кл.слова: ЧАС ОБРОБКИ, ОБЕРТАЛЬНЕ ТОЧІННЯ, ШОРСТКІСТЬ ПОВЕРХНІ
Strelchuk, R. Surface roughness modeling during electric discharge grinding with variable polarity of electrodes / R. Strelchuk. - P .77-84. - Bibliography is at the end of the article
Кл.слова: ПРОСТОРОВЕ ПОЛОЖЕННЯ ЕРОЗІЙНИХ ЛУНОК, СТАТИСТИЧНІ РОЗМІРИ, ПАРАМЕТРИ ШОРСТКОСТІ
Tihenko, V. Automatic control of temperature and power conditions during rough grinding of slabs / V. Tihenko, V. Lebedev, T. Chumachenko. - P .85-91. - Bibliography is at the end of the article
Кл.слова: ОБДИРНЕ ШЛІФУВАННЯ, УПРАВЛІННЯ ТЕМПЕРАТУРОЮ ШЛІФУВАННЯ СЛЯБУ, АПЕРІОДИЧНА ЛАНКА
Fedorovich, V. Modeling the influence of metal phase in diamond grains on self-sharpening of grinding wheels on ceramic bonds / V. Fedorovich [and etc.]. - P .92-101. - Bibliography is at the end of the article
Інші автори: Fedorenko D., Pyzhov I., Ostroverkh Y.
Кл.слова: АЛМАЗНИЙ КРУГ, ОБРОБЛЮВАНИЙ МАТЕРІАЛ, НАПРУЖЕНО-ДЕФОРМОВАНИЙ СТАН
Chumak, A. Finish machining of the cutting inserts from cubic borine nitride BL group composite / A. Chumak [and etc.]. - P .102-114. - Bibliography is at the end of the article
Інші автори: Klimenko S., Klimenko S., Manokhin A., Naydenko A., KopeikinaM., Burikin V., Bondarenko M., Burlakov V.
Кл.слова: АЛМАЗНА ОБРОБКА, ВІБРО-МАГНІТНО-АБРАЗИВНА ОБРОБКА, РІЗАЛЬНІ ПЛАСТИНИ
Yakimov, A. Influence of the geometric characteristics of the discontinuous profile working surfaces of abrasive wheels for precision and temperature when grinding / A. Yakimov [and etc.]. - P .115-125. - Bibliography is at the end of the article
Інші автори: Bovnegra L., Tonkonogyi V., VaysmanV., Strelbitskyi V., Sinko I.
Кл.слова: МАКРОТОПОГРАФІЯ РОБОЧОЇ ПОВЕРХНІ, ШОРСТКІСТЬ ПОВЕРХНІ, СТУПІНЬ ВІДПУЩЕННЯ
Yakovenko, I. Technological provision of the accuracy for the thread form of rod pumps / I. Yakovenko, Yu. Vasilevskyi, Y. Basova. - P .126-134. - Bibliography is at the end of the article
Кл.слова: РІЗЬБОВЕ З’ЄДНАННЯ, ПРОФІЛЬ РІЗЬБЛЕННЯ, МАТЕМАТИЧНЕ МОДЕЛЮВАННЯ
Klymenko, G. Quality management of cutting tools on heavy machines / G. Klymenko, Y. Vasylchenko, Ye. Donchenko. - P .135-141. - Bibliography is at the end of the article
Кл.слова: УПРАВЛІННЯЯКІСТЮ, РІЗАЛЬНИЙ ІНСТРУМЕНТ, ВЕРСТАТИ
Garashchenko, Ya. Evaluation of the forecasted efficiency of performance of rational orientation of the product in the workspace of additive installations / Ya. Garashchenko, N. Zubkov. - P .142-150. - Bibliography is at the end of the article
Кл.слова: ТЕХНОЛОГІЧНА ПІДГОТОВКА, АДИТИВНІ ТЕХНОЛОГІЇ, ТРІАНГУЛЯЦІЙНА МОДЕЛЬ
ДРНТІ
УДК

Кл.слова (ненормовані):
ТЕПЛОПРОВІДНІСТЬ ПОКРИТТЯ -- ТОКАРНА ОБРОБКА -- АБРАЗИВНА ОБРОБКА -- АЛМАЗНІ ІНСТРУМЕНТИ -- КОМПОЗИЦІЙНІ МАТЕРІАЛИ -- ШЛІФОВАЛЬНІ ВЕРСТАТИ -- ТОКАРНІ ВЕРСТАТИ
Есть полнотекстовые версии (доступ потребує авторизації)

Дод.точки доступу:
Грабченко, Анатолій Іванович (доктор технічних наук ; 1935) \голов. ред.\
Грабченко, Анатолий Иванович (доктор технических наук ; 1935)
Logominov, V.
Ostroverkh, Y.
Manokhin, A.
Naydenko, A.
KopeikinaM.
Burikin, V.
Bondarenko, M.
Burlakov, V.
VaysmanV.
Strelbitskyi, V.
Sinko, I.

Примірників усього: 1
аб.1 (1)
Вільні: аб.1 (1)